EasyTherm 30 HQ Induction Bearing Heater

Special Price $6,495.00 Regular Price $6,900.00
Mitchell Part Number
PON-ET30HQ
Manufacturer
Availability
Typically in stock, Call if Urgent
Quick overview

TM Induction's Easy therm 30 is a powerful 400 Volt stationary microprocessor controlled induction heater with an ergonomic pivoting yoke, to be used for the professional mounting of a range of parts including bearings, typically used in maintenance shops and production areas.

EASYTHERM 30 is powerful 12.8 kW induction heater with an ergonomic pivoting yoke. Since the EasyTherm 30 induction heater is microprocessor controlled, a temperature transfer can be implemented within 2 degrees celcius of desired temp. or timed to a fraction of a second. The unit is customizable, in the fact that, you specify voltage, yoke crossbars, and any extentions needed. With the right configuration, this induction heater can accommodate bearing assemblies, and other parts, over a meter in diameter. Upon completion of heating, no more than 2 A/cm of residual magnetism is left behind.

“TURBO-BOOST” - In the horizontal position the part will heat up twice as fast.

The pivoting yoke has the great advantage that only the work piece is handled, because the arm does not have to be lifted manually. This avoids unnecessary handling and reduces the risk of dirt intruding into the bearing or work piece.

New Features on EasyTerm 30HQ

  • Easy to use; the process is entirely microprocessor controlled. The operator only needs to set the temperature or time, other features like power reduction will be automatically recognized.
  • Electronic Thyristor now has double capacity and will be cooled continuously via the large integral heat sink allowing for continuous operation.
  • Circuit Board print-tracks and wire sizes greatly increased for greater reliability
  • Temperature of the heat sink, power coil, and housing are constantly monitored by the microprocessor. If any limit is exceeded, the heater will signal an alarm and shutoff. No damage to the heater or the part!

Features

  • Fast controllable heating process.
  • Safe heating process; only the work piece is heated.
  • Elimination of hot oil bath, no risk of localized overheating.
  • Suitable for sealed and shielded bearings.
  • Suitable for pre-greased bearings.
  • Suitable for bearings with polyamide cages.
  • Manufactured according to the CE Regulations.
  • Fast heating process through high output; Cos phi > 0.8.
  • The heating coil is placed horizontal under the part:
    • By this it is impossible to damage the coil
    • This ensures an equal temperature all over the part (inner- and outer ring).
    • This makes it able to heat up parts with smaller bores.
  • All heaters are continuously useable without any optional cooling system.
  • Constantly monitoring heating process by probe and microprocessor.
  • Temperature control accuracy +/- 2°C.
  • Timer accuracy 0.01 sec.
  • Maintenance free.
  • Three years warranty.
  • Easy to use; user friendly design.
  • Ergonomic design (pivoting yoke principle).
  • Automatic power regulation, no manual pre-setting necessary.
  • Less than 2A/cm residual magnetism.
  • More Information
    Weight 500.000000
    Specifications

    Technical information

    Voltage:

    380-480V
    Frequency: 50 or 60Hz
    Power:
    12.8kVA
    Heater mass:
    60kg (132lbs)
    Dimensions: 880x320x570mm
    Temp. mode: Max. 240/400°C
    Width U-core: 330mm
    Height U-core: 295mm

     

    OPTIONAL YOKES

    Size induction yokes mm 
    Minimum Bore
    Maximum Outer Diameter
    Maximum Width
    Maximum Outer Diameter
    with adapter yoke 70x70x150
    Maximum Width
    with adapter yoke
    70x70x150
    20x20x490
    non-pivoting
    30mm
    620mm
    330mm 
    910mm
    330mm
    30x30x490
    non-pivoting
    45mm
    630mm
    330mm
    920mm
    330mm
    40x40x490
    pivoting
    55mm
    640mm
    330mm
    930mm
    330mm
    50x50x490
    pivoting
    70mm
    650mm
    330mm
    940mm
    330mm
    60x60x490
    pivoting

    85mm

    660mm

    330mm

    950mm

    330mm

    70x70x490
    pivoting

    100mm

    670mm

    330mm

    960mm

    330mm

    80x80x490
    pivoting

    115mm

    740mm

    330mm

    960mm

    330mm

    Manufacturer TM Induction
    MPN Easytherm 30
    You're reviewing: EasyTherm 30 HQ Induction Bearing Heater
    Your Rating